Thema erstellen
Foren
Neue Beiträge
Foren durchsuchen
Aktuelles
Neue Beiträge
Neueste Aktivitäten
Blog
Anmelden
Registrieren
Aktuelles
Suche
Suche
Nur Titel durchsuchen
Von:
Neue Beiträge
Foren durchsuchen
Menü
Anmelden
Registrieren
App installieren
Installieren
Foren
Reparaturtips braune Ware
Reparatur von LCD Plasma Fernsehern sowie Beamer
LG 49UB850V LG 49UB850V schaltet nicht ein, Standby LED aus, blinkt 3x beim einschalten
JavaScript ist deaktiviert. Für eine bessere Darstellung aktiviere bitte JavaScript in deinem Browser, bevor du fortfährst.
Du verwendest einen veralteten Browser. Es ist möglich, dass diese oder andere Websites nicht korrekt angezeigt werden.
Du solltest ein Upgrade durchführen oder einen
alternativen Browser
verwenden.
Auf Thema antworten
Beitrag
<blockquote data-quote="Seb932" data-source="post: 376924" data-attributes="member: 86602"><p>P201 ist auf dem NT und hat 28Pins, davon gehen aber 4 (SIN;V-SYNC;SCLK;GND) auf das T-CON Board und 24 auf den P13002 auf dem MB, daher der Unterschied.</p><p></p><p>Den Hinweis mit dem IC3000 werde ich auf jedem Fall mal nachgehen. Dieser steuert ja auch die Standby-LED (LED_R) welche ebenfalls fehlerhaft anzeigt. Viel mehr als der Microcontroller scheint ja direkt nach dem Anstecken auf dem Mainboard nicht zu leben.</p><p>Ich werde die Tage mal die Resetprozedur mit dem Oszi nachverfolgen....</p><p></p><p>Aus der Testroutine vom 55EC9300, klingt sehr ähnlich...</p><p>(1) When AC is applied to the SMPS, it outputs 3.5V_ST to the Main board, P2300 pins 3, 5 and 6. This 3.5V is routed through</p><p>L2304 and on to the Microprocessor IC3000 pin 48 as its main power source. The 3.5V also goes to the Reset circuit. At the</p><p>moment 3.5V arrives at C3004 (+) side, the capacitor isn’t charged, so pin 40 of the Micro is low while the power input pin 48 is</p><p>high. This is known as the reset state, where the Microprocessor is reset to the first operational state. As C3004 charges</p><p>through R3030, pin 40 pulls up and the Micro comes out of Reset. The TV is now in the Stand-By state.</p><p>The 3.5V is also routed to pull-up resistors to the Key 1 and 2 lines. It is also sent to the IR receiver and as source voltage for</p><p>the Power on switch Q2300, but it is not on at this time.</p></blockquote><p></p>
[QUOTE="Seb932, post: 376924, member: 86602"] P201 ist auf dem NT und hat 28Pins, davon gehen aber 4 (SIN;V-SYNC;SCLK;GND) auf das T-CON Board und 24 auf den P13002 auf dem MB, daher der Unterschied. Den Hinweis mit dem IC3000 werde ich auf jedem Fall mal nachgehen. Dieser steuert ja auch die Standby-LED (LED_R) welche ebenfalls fehlerhaft anzeigt. Viel mehr als der Microcontroller scheint ja direkt nach dem Anstecken auf dem Mainboard nicht zu leben. Ich werde die Tage mal die Resetprozedur mit dem Oszi nachverfolgen.... Aus der Testroutine vom 55EC9300, klingt sehr ähnlich... (1) When AC is applied to the SMPS, it outputs 3.5V_ST to the Main board, P2300 pins 3, 5 and 6. This 3.5V is routed through L2304 and on to the Microprocessor IC3000 pin 48 as its main power source. The 3.5V also goes to the Reset circuit. At the moment 3.5V arrives at C3004 (+) side, the capacitor isn’t charged, so pin 40 of the Micro is low while the power input pin 48 is high. This is known as the reset state, where the Microprocessor is reset to the first operational state. As C3004 charges through R3030, pin 40 pulls up and the Micro comes out of Reset. The TV is now in the Stand-By state. The 3.5V is also routed to pull-up resistors to the Key 1 and 2 lines. It is also sent to the IR receiver and as source voltage for the Power on switch Q2300, but it is not on at this time. [/QUOTE]
Zitate einfügen...
Authentifizierung
Anzahl der Ecken eines Dreiecks plus Eins?
Antworten
Foren
Reparaturtips braune Ware
Reparatur von LCD Plasma Fernsehern sowie Beamer
LG 49UB850V LG 49UB850V schaltet nicht ein, Standby LED aus, blinkt 3x beim einschalten
Oben