G
gonzo0815
Benutzer
- Registriert
- 30.01.2006
- Beiträge
- 234
- Punkte Reaktionen
- 3
Hallo allerseits,
ich habe eine grundsätzliche Frage zur UG2 Spannung. Es gibt immer wieder die zwei Vorgehensweisen, zum einstellen der UG2 Spannung:
1. UG2 auf den exakten (vom Hersteller spezifizierten )Wert aus dem Service Manual abgleichen (mittels Multimeter messen), fertig.
2. Service Menü G2 Alignment, G2 aufdrehen bis Rücklauflinien erkennbar, so weit drehen bis Linien verschwinden und noch etwas weiter.
Etwas ausführlicher steht dies so in der Repairfaq:
"The screen should be adjusted with a white pattern (snow from the tuner should do or turn the user COLOR control all the way down to get a black and white picture). Put the set in Service mode (horizontal line) if it has such a switch in the back or inside. If not, just use the raster in a darkened room. Adjust screen for a dim white line (raster). If the line is not white at its dimmest point, you will need to adjust the drive and cutoff controls for R, G, & B.
Alternatively, you can use the following procedure:
Turn R, G, and B screen (or background) controls down. Now turn color control fully counterclockwise -- off. Now turn up red screen until the screen just shows a red hue. Now turn red gun down until red tint just goes away. Now do the same with the green and blue screen controls. Now adjust the two DRIVE controls for the best black and white picture. That`s all there is to it. I don`t like to work with just a thin "SETUP" line. Cartoons seem to be the best thing to have on while doing the above procedure. You can also use just plain snow (no program) if you prefer. If you can obtain a good b@w pic. when you`re done, the tube is good and the set if most likely functioning properly. Be patient and go slow while watching the large mirror that you are using during this procedure. (LEE) "
(repairfaq.org/samnew/tvfaq/tvadjscc.htm)
Nun widerspricht die 2 Variante ja ganz eindeutig gegen die Herstellerangaben (z.B. bei Thomson ICC20: stur 384V), da die UG2 ja dann eher zufällig sein wird.
Wenn ich das richtig verstehe, so berücksichtigt die 2. Variante das altern der BiRö und man gleicht quasi die nachlassende Leuchtkraft durch eine höhere UG2 aus.
Hat eine höhere UG2 Nachteile für die BuRö?
ich habe eine grundsätzliche Frage zur UG2 Spannung. Es gibt immer wieder die zwei Vorgehensweisen, zum einstellen der UG2 Spannung:
1. UG2 auf den exakten (vom Hersteller spezifizierten )Wert aus dem Service Manual abgleichen (mittels Multimeter messen), fertig.
2. Service Menü G2 Alignment, G2 aufdrehen bis Rücklauflinien erkennbar, so weit drehen bis Linien verschwinden und noch etwas weiter.
Etwas ausführlicher steht dies so in der Repairfaq:
"The screen should be adjusted with a white pattern (snow from the tuner should do or turn the user COLOR control all the way down to get a black and white picture). Put the set in Service mode (horizontal line) if it has such a switch in the back or inside. If not, just use the raster in a darkened room. Adjust screen for a dim white line (raster). If the line is not white at its dimmest point, you will need to adjust the drive and cutoff controls for R, G, & B.
Alternatively, you can use the following procedure:
Turn R, G, and B screen (or background) controls down. Now turn color control fully counterclockwise -- off. Now turn up red screen until the screen just shows a red hue. Now turn red gun down until red tint just goes away. Now do the same with the green and blue screen controls. Now adjust the two DRIVE controls for the best black and white picture. That`s all there is to it. I don`t like to work with just a thin "SETUP" line. Cartoons seem to be the best thing to have on while doing the above procedure. You can also use just plain snow (no program) if you prefer. If you can obtain a good b@w pic. when you`re done, the tube is good and the set if most likely functioning properly. Be patient and go slow while watching the large mirror that you are using during this procedure. (LEE) "
(repairfaq.org/samnew/tvfaq/tvadjscc.htm)
Nun widerspricht die 2 Variante ja ganz eindeutig gegen die Herstellerangaben (z.B. bei Thomson ICC20: stur 384V), da die UG2 ja dann eher zufällig sein wird.
Wenn ich das richtig verstehe, so berücksichtigt die 2. Variante das altern der BiRö und man gleicht quasi die nachlassende Leuchtkraft durch eine höhere UG2 aus.
Hat eine höhere UG2 Nachteile für die BuRö?