D-Box 2 Philips Sat kein Empfang mehr

[masterman]

Hersteller: Philips
Typenbezeichnung: D-Box2
Chassi:

Vorhandene Messgeräte: Digital oder Analogvoltmeter
Schaltplan vorhanden: Nein
Dein Wissensstand: Einsteiger

Fehlerbeschreibung und Nachricht:
Hallo Ihr Lieben.

Kleines Problem mit großer Wirkung.

Meine D-Box 2 Sat, GLJ Image, empfängt keine Sender mehr.
Das kam von jetzt auf gleich.

Spannung am Satkabeleingang bei ARD - Das Erste 18,5 V

Satfinder zeigt folgendes an: Ohne Satkabel

3 Balken v. oben n. unten.

1. ber Vollanschlag
2. snr ca. 1/5 vom Balken, Wert ~ 12375 (schwankend)
3. sig kein Balken, wert =
Darunter, No Signal

Satfinder mit Satkabel und perfekt ausgerichteter Satschüssel und neuem LNB.

1. ber Vollanschlag
2. snr 1/5 bis 1/2 (50%) schwankend, mal mehr mal weniger)
3. sig 1/2 (~ 50%)
Darunter ??? schwankend zu No Signal

Hier der Log der Box:

debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.0 mID 02
debug: feID 00 enxID 03
debug: fpID 52 dsID 01-0a.3e.c5.07.00.00-16
debug: HWrev 01 FPrev 0.30
debug: B/Ex/Fl(MB) 32/00/08
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/philips-dbox2/kernel/os in Flash-FS
debug: Got Block #0040

will verify ELF image, start= 0x800000, size= 149536
verify sig: 262
Branching to 0x40000


U-Boot 1.1.4 (Tuxbox) (Dec 7 2006 - 12:37:2

CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Philips, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ............ done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 650877 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 650813 Bytes = 635.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34-dbox2 (GLJ-Team@DBOX2) (gcc version 3.4.4) #4 Sa Apr 21 21:
03:42 CEST 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw console=ttyS0
Decrementer Frequency = 247125000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)
Console: colour dummy device 80x25
Calibrating delay loop... 65.53 BogoMIPS
Memory: 30864k available (1104k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (2002081 Richard Gooch (http://glj.6x.to 0:0 (TDA8044H QPSK Demodulator)...
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_av_core: Starting avia_gt_wdt thread.
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
avia_gt_proc: Using config file '/var/tuxbox/config/avia.conf'.


avia_gt_proc: $Id: avia_gt_proc.c,v 0.92d 2003/06/18 19:00:00 bofh Exp $

avia_gt_proc: found - AVIA eNX

Please press Enter to activate this console. rm: cannot remove `/var/etc/.slot0_
start': No such file or directory
rm: cannot remove `/var/etc/.slot1_start': No such file or directory
rm: cannot remove `/var/etc/.slot_com': No such file or directory
rm: cannot remove `/var/etc/.slot_multi': No such file or directory
rm: cannot remove `/var/etc/.com_betad': No such file or directory
rm: cannot remove `/var/etc/.multi_betad': No such file or directory
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
ping: http://www.google.com: Host name lookup failure
$Id: zapit.cpp,v 1.395 2007/03/17 21:34:22 houdini, patched by GLJ-Team (JohnDoe
) Exp $
[zapit] PMT update enabled
ping: http://www.yahoo.com: Host name lookup failure
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
[getservices] /var/tuxbox/config/zapit/myservices.xml found.
[getservices] dup transponder id 1 onid 85
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 43E onid 1
[getservices]: removing 'KIOSQUE' (service_id=0x20de): FAILED!
[getservices] dup transponder id 438 onid 1
[getservices] dup transponder id 442 onid 1
[getservices] dup transponder id 412 onid 1
/tmp/currentservices.xml: No such file or directory
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
$Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $

[controld] Boxtype detected: (2, Philips D-BOX2)
[controld]: ROUTEVIDEO v1 = 1 a1 = 1 v2 = 1 a2 = 1 v3 = 1 a3 = 1 fblk=1
SET VSW: 0 1
SET VSW: 1 1
SET VSW: 2 1
[controld] setting VideoFormat to auto
[CBasicClient] connect failed.
/tmp/sectionsd.sock: No such file or directory
[nhttpd] Neutrino HTTP-Server starting......Patched GLJ-Team (JohnDoe)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
$Id: sectionsd.cpp,v 1.237 2007/03/29 15:43:32 mws Exp $
[sectionsd] Caching max 4000 events
[sectionsd] Caching 7 days
[sectionsd] Events are old 360min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
/tmp/neutrino: /lib/libpng12.so.0: no version information available (required by
/tmp/neutrin
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[basicsocket] send_data: Resource temporarily unavailable
[deutsch.locale] superfluous entry: flashupdate.currentdistribution
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[basicsocket] send_data: Resource temporarily unavailable
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[basicsocket] send_data: Resource temporarily unavailable
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
/dev/input/event1: No such file or directory
[neutrino] menue setup
[controld] setting VideoFormat to auto
loading locales: scandir: No such file or directory
[neutrino] received 18 sats
[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[controld] setting VideoFormat to auto
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out


Hat wer ne Ahnung?
Ich nämlich nicht.

 

[dboxer]

Ram defekt SEC defekt FP defekt

kommen 22 khz noch raus ?

 

[masterman]

woran kann ich erkennen das 22 khz noch kommen?

 

[dboxer]

mitm oscar

 

[masterman]

mitm oscar

hab ich aber nicht.

und nu?
Lohnt sich noch was?
Real?

 

[dboxer]

rep dürfte so um die 40 euro liegen

aber dazu muss der techniker das gute stück auf dem tisch haben um genaueres zu sagen

 

[masterman]

danke für deine Hilfe.

Woran erkennst Du dass die Komponenten defekt sind?
Und der Tuner ist ok?
Man das wäre echt super.
Aber ich hab noch was vergessen:

Auf der Rückseite des Mainboards ist ein Kabel das nur auf einer Seite Verbindung zum Board hat, ich füge mal ein Bild an: Im Kreis das Ende ohne Verbindung.
Frage, kann das was damit zu tun haben? mein anderer Philips Receiver hat das Kabel nicht.

 

[dboxer]

indem ich die messegräte einschalte und den fehler ausmesse was das kabel soll weiss ich auch net ist aber orginal nicht drinn